您好,欢迎来到贵州AG8工程机械有限公司官网!

贵阳装载机

新闻分类

产品分类

联系AG8

公司名称:贵阳AG8工程机械有限公司


联系人:杨经理


手  机:15186981858

            

网  址:www.bastard-divine.com


邮箱:1721318949@qq.com


地  址:贵州省贵阳市观山湖区金华镇金华小学后面


装载机日常检查和保养

您的当前位置: 贵州装载机出租 >> 新闻中心 >> 公司新闻

装载机日常检查和保养

发布日期:2018-02-05 作者:贵阳直喷装载机 点击:

装载机日常检查和保养

贵阳直喷装载机

Daily inspection and maintenance of loader

贵阳直喷装载机提醒安全生产是工作的前提,所以一定要做好装载机日常的检查与保养。

Guiyang direct injection loader reminding safety production is the premise of work, so we must do a good job of the daily inspection and maintenance of the loader.

每天作业前和作业后必须绕机检查。以确保作业的安全。检查内容如下:

Every day before and after operation must be checked around the machine. To ensure the safety of the operation. The contents of the inspection are as follows:

1、 检查各工作灯,指示灯等是否破损,电、气、油的线路、管路是否老化或破损。

1, check the work lights, indicator lights and other breakages, electricity, gas, oil lines, pipelines are old or damaged.

2、 检查发动机空滤器的灰尘,是否影响进气效果。

2, check the dust of the engine air filter, whether it affects the effect of air intake.

3、 检查前、后传动轴的连接螺栓是否有松动、脱落现象,锁紧力为530N.M。

3, check whether the connecting bolt before and after the transmission shaft has loose and shedding phenomena, and the locking force is 530N.M.

4、 检查各销轴等连接螺栓是否松动。

4, check whether the pin shaft and other connecting bolts are loose.

5、 检查轮胎有否破损,充气是否足够(前轮:0.30-0.32MPa,后轮:0.28-0.30 MPa)。轮胎气压必须控制在规定的范围内。轮胎螺栓是否松动,锁紧力为830N.M。

5, check whether the tire is damaged or not enough to inflate (front wheel: 0.30-0.32MPa, rear wheel: 0.28-0.30 MPa). The tire pressure must be controlled within the specified range. Whether the tire bolts are loose and the locking force is 830N.M.

6、 检查是否有漏油、漏水、漏电、漏气现象。

6, check whether there are leakage, leakage, leakage of electricity, leakage of gas.

7、 检查水位,变速箱油位,液压油油位,刹车油油位。

7, check water level, gearbox oil level, hydraulic oil level, brake oil level.

8、 对各油咀加注油脂。

8. Add oil to each oil Tsui.

9、 检查刹车片磨损情况。

9. Check the wear of the brake disc.

10、 检查铲斗刀刃及斗齿的磨损情况,当刀刃磨损10cm,斗齿磨损超过全长的1/4时需修复或更换。

10, check the wear of the blade and the bucket teeth of the bucket. When the blade wears 10cm, the bucket teeth wear more than the full length of 1/4, it needs to be repaired or replaced.

11、拆缷安装蓄电池时应分清正极、负极,并且要牢牢地拧紧螺母,拆缷时应首先脱开负极(接地端)。

11, disassemble the battery installation should distinguish between the anode and the cathode, and tighten the nut firmly, disassemble should first release the negative (ground).

12、避免金属物体(如:工具等)与蓄电池端子意外接触,造成短路。

12, avoid metal objects (such as: tools, etc.) and accidental contact with the battery terminal, causing short circuit.

13、蓄电池电解液内含有硫酸,而且能产生氢气,要避免烟头和明火靠近蓄电池。如果硫酸液濺入皮肤、眼睛内应立即用大量清水冲洗,严重时应立即到医院治疗。

13, the battery electrolyte contains sulphuric acid, and can produce hydrogen, so as to avoid the cigarette end and the open fire near the battery. If the sulphuric acid is splashed into the skin and the eyes should be immediately washed with a large amount of water, it should be treated immediately to the hospital.

14、刚刚停止作业时,发动机的冷却液,所有零件中的油,排气管和消声器都处在高温下,如果拆缷盖子或排油或更换滤油器等都会造成烫伤或其它伤害,应等待温度降下来后再进行保养和检查。

14, just stop operation, the engine coolant, all parts of the oil, the exhaust pipe and the muffler are in high temperature, if the lid disassemble or discharge of oil or replacement of oil filter will cause burns or other injuries, should wait for the temperature drop down after maintenance and inspection.


本文网址:http://www.bastard-divine.com/news/226.html

关键词:贵阳直喷装载机,直喷装载机,直喷装载机厂家

上一篇:没有了
下一篇:装载机机油压力过低的几个原因

最近浏览:

  • 在线客服
  • 联系电话
    13885175275
  • 在线留言
  • 在线咨询
    欢迎给AG8留言
    请在此输入留言内容,AG8会尽快与您联系。
    姓名
    联系人
    电话
    座机/手机号码
    邮箱
    邮箱
    地址
    地址