您好,欢迎来到贵州AG8工程机械有限公司官网!

贵阳装载机

新闻分类

产品分类

联系AG8

公司名称:贵阳AG8工程机械有限公司


联系人:杨经理


手  机:15186981858

            

网  址:www.bastard-divine.com


邮箱:1721318949@qq.com


地  址:贵州省贵阳市观山湖区金华镇金华小学后面


贵州直喷装载机销售告诉你装载机操作规范

您的当前位置: 贵州装载机出租 >> 新闻中心 >> 专题报道

贵州直喷装载机销售告诉你装载机操作规范

发布日期:2018-02-05 作者:贵州直喷装载机销售 点击:

贵州直喷装载机销售告诉你装载机操作规范

Guizhou direct injection loader sales tell you the loader operation specification

贵州直喷装载机销售

好的操作习惯让您的设备寿命延长一倍

Good operating habits have doubled the life of your equipment.


1、铲斗运输高度

1, shovel transportation height


违规操作:带负荷高举动臂行走装车,容易造成动臂油缸弯曲的故障。

Illegal operation: loading high arm with a load, easy to cause the fault of the arm cylinder bending.


标准操作:收斗状态,铲斗底部离地40-50公分,坡道上尽量降低。

Standard operation: the bucket state, the bottom of the bucket is 40-50 centimeters away from the ground, and the slope is reduced as much as possible.


2、作业时,应使装载机直对前方,前后车架应在一条直线上。

2. When working, the loader should be straight to the front, and the front and rear frame should be in a straight line.


3、禁止利用惯性高速插入料堆,应靠装载机的驱动力直线切入。

3. Prohibit the use of inertial high-speed inserts, which should be cut into a straight line by the driving force of the loader.


4、铲斗切入角过大,负荷全部加到前桥,造成后轮悬空,容易出现前桥主从动螺旋打齿、半轴甚至前桥支承轴断裂等故障。

4, the entry angle of the bucket is too large and the load is all added to the front axle, resulting in the rear wheel suspension. It is easy to appear the failure of the front axle, the driven spiral, the half axle or even the front axle supporting shaft fracture.


5、禁止用铲斗一角铲掘硬质物料,否则极易出现动臂变形、油缸损坏等故障。

5. It is forbidden to use a shovel to dig hard materials. Otherwise, it is very easy to have the fault of the deformation of the arm and the damage of the oil cylinder.


6、铲斗插入料堆后,应先收斗再起动臂,否则会造成动臂变形。

6. After the bucket is inserted into the heap, the arm should be reacted to the bucket first, otherwise the deformation of the arm will be caused.


7、带负荷高举动臂行走装车,容易造成动臂油缸弯曲的故障。

7, with the load high lift arm walking loading and loading, it is easy to cause the fault of the arm cylinder bending.


8、不可在高位进行挖掘作业或用铲斗磕碰物料,以免动臂油缸弯曲。

8, can not carry out mining operations or bucket bump material in the high, to avoid the boom cylinder bending.


9、卸料后,应先收斗或部分收斗再操作动臂,否则会造成“拔缸”,损坏翻斗油缸。

9, after unloading, we should first collect the bucket or part of the bucket to operate the arm, otherwise it will cause "pull out the cylinder" and damage the bucket oil cylinder.


10、铲斗各限位块经长时间撞击致变形、磨损后,要及时进行补焊,保证铲斗各限位块在正常收斗、卸料位置起到有效的限位作用。

10, after the long distance impact and deformation and wear of the bucket blocks, the repair welding should be carried out in time to ensure that the stopper blocks play an effective limiting role in the normal receiving and unloading position.


贵州直喷装载机销售认为如限位块磨损过度不及时补焊,会造成摇臂变形、断裂的故障!

Guizhou direct injection loader sales think that if the limit block wear too much less timely repair welding, will cause the rocker arm deformation, fracture failure!


11、涉水作业时,水面不要超过驱动桥或变速箱输出轴油封的最低部位。

11. When wading operation, the water surface should not exceed the lowest part of the drive axle or the transmission shaft of the gearbox.


12、船舱、井下作业工况,发动机须安装尾气处理装置。贵州直喷装载机销售小编今天就分享到这里了。

12, the operating conditions of the cabin and downhole operation, the engine must install the tail gas treatment device. Guizhou direct injection loader sales small editor today is shared here.

  


本文网址:http://www.bastard-divine.com/news/335.html

关键词:贵州直喷装载机销售,直喷装载机销售,贵阳直喷装载机销售

最近浏览:

  • 在线客服
  • 联系电话
    13885175275
  • 在线留言
  • 在线咨询
    欢迎给AG8留言
    请在此输入留言内容,AG8会尽快与您联系。
    姓名
    联系人
    电话
    座机/手机号码
    邮箱
    邮箱
    地址
    地址