您好,欢迎来到贵州AG8工程机械有限公司官网!

贵阳装载机

新闻分类

产品分类

联系AG8

公司名称:贵阳AG8工程机械有限公司


联系人:杨经理


手  机:15186981858

            

网  址:www.bastard-divine.com


邮箱:1721318949@qq.com


地  址:贵州省贵阳市观山湖区金华镇金华小学后面


装载机变速器油面升高或降低故障的判断方式是什么?

您的当前位置: 贵州装载机出租 >> 新闻中心 >> 行业新闻

装载机变速器油面升高或降低故障的判断方式是什么?

发布日期:2018-02-05 作者:贵州装载机 点击:

装载机变速器油面升高或降低故障的判断方式是什么?

贵州装载机

贵州装载机">What is the way to judge the oil surface of the loader transmission or to reduce the failure?

装载机是一种工程机械,通常情况下工作环境恶劣,这样就难免造成设备出现或大或小的各种毛病,下面贵州装载机工程师就给大家介绍下变速器油面升高或降低故障的判断方法。

Loader is a kind of construction machinery, usually working environment is bad, so it will inevitably cause all kinds of defects of equipment. Large scale or small scale will inevitably happen. Next, Guizhou loader engineer will tell you how to increase or decrease the fault of transmission oil.

贵州直喷装载机销售认为装载机变速器油面升高或降低的现象俗称“倒油”。油面升高的现象在实际修理中较常见,一般是由于工作泵或转向泵轴端骨架油封损坏所致。但在判断故障时,如果分别将工作泵或转向泵拆下来检查,既繁琐,又浪费进间,贵州装载机工程师给大家介绍一个简易判断方法供参考。

The sales of Guizhou direct injection loader think the rising or lowering of the oil surface of the loader is commonly known as "oil dumping". The rise of oil surface is more common in actual repair, usually due to the damage of the shaft end of the working pump or the shaft end of the steering pump. But when judging the fault, if the work pump or the steering pump is removed separately, it will be cumbersome and wasteful. The Guizhou loader engineer will introduce a simple judgement method for your reference.

将工作泵的4个固定螺钉松开,并向外移开,使工作泵与变泵之间有少量缝隙。然后,起动装载机并操纵动臂及转斗缸作动作,如果发现从缝隙处漏油(严重时呈油流状,轻微点是断续滴油),即可判定是工作泵轴端骨架油封损坏,否则须检查转向泵;出可以用相同方法,只不过起动装载机后左右打转向盘,如果漏油,即可判定是转向泵轴端骨架油封损坏。一般情况下,可分别更换轴端骨架油封进行排除。

The 4 fixed screws of the work pump are loosened and moved outward, so that there is a small gap between the work pump and the variable pump. Then, starting loader and manipulation of the movable arm and bucket cylinder action, if found leaking from the gap (which is the flow of oil, slight is intermittent drops of oil), can judge the work pump shaft skeleton oil seal is damaged, or to check the steering pump; can use the same method, just starting after the loader around the steering wheel, if the leakage can be determined, is steering pump shaft end seal damage. In general, the shaft end skeleton oil seal can be replaced separately.

加速器油面降低的现象较少出现,在判断此故障时,首先应检查变速器前后输出轴处及其他油管处是否漏油,如果不漏油,则可确定是变速泵油封损坏及工作泵油封装配不当引起。更换变速泵油封或变速泵总成后即或排除故障。

The phenomenon of reduction of accelerator oil surface is less. When judging this fault, we should first check whether oil leakage occurs at the output shaft and other tubing of transmission before and after transmission. If there is no oil leakage, it can be determined that the oil seal of the speed change pump is damaged and the pump oil package is mismatched. Change the pump seal or variable speed pump assembly or troubleshooting.

实践证明,采用这种检查方法,操作方便,省时省力,且效果比较好。

It has been proved by practice that this method is convenient to operate, save time and labor, and the effect is better.


本文网址:http://www.bastard-divine.com/news/354.html

关键词:贵州装载机,贵州装载机公司,贵州装载机厂家

最近浏览:

  • 在线客服
  • 联系电话
    13885175275
  • 在线留言
  • 在线咨询
    欢迎给AG8留言
    请在此输入留言内容,AG8会尽快与您联系。
    姓名
    联系人
    电话
    座机/手机号码
    邮箱
    邮箱
    地址
    地址