您好,欢迎来到贵州AG8工程机械有限公司官网!

贵阳装载机

新闻分类

产品分类

联系AG8

公司名称:贵阳AG8工程机械有限公司


联系人:杨经理


手  机:15186981858

            

网  址:www.bastard-divine.com


邮箱:1721318949@qq.com


地  址:贵州省贵阳市观山湖区金华镇金华小学后面


装载机滤芯的更换步骤是什么?

您的当前位置: 贵州装载机出租 >> 新闻中心 >> 专题报道

装载机滤芯的更换步骤是什么?

发布日期:2018-02-05 作者:贵阳直喷装载机 点击:

装载机滤芯的更换步骤是什么?

What is the replacement step of the loader filter core?

贵阳直喷装载机

贵阳装载机滤芯正常情况1000-1500小时更换一次,环境特别恶劣的使用场所,建议每500小时更换空气滤芯。清洁或更换空滤芯时,部件是必须一一合对,严防异物落入进气阀。贵州装载机滤芯设计破坏压差为4bar,压缩机

Guiyang loader filter core normal condition 1000-1500 hours change, the environment is very bad use place, recommended every 500 hours to replace the air filter. When cleaning or replacing the air filter, the components must be fitted one by one to prevent the foreign body from falling into the intake valve. Guizhou loader filter core design failure pressure difference is 4bar, compressor


贵阳直喷装载机认为升压后应逐渐打开计算所阀直到达到负荷用气量需要,绝对严禁突然放空,致使滤芯精分离层破裂和滤芯压扁,而大量携油。超出油气分离滤芯设计流速范围使用,油携带量必然会增加。

After increasing the pressure, the valve should be opened gradually until the load of gas is needed. It is strictly forbidden to empty suddenly, resulting in the fine separation of the filter core, the separation of the layer and the flattening of the filter element, and a large number of oil carrying. When the oil and gas separation filter is used to design the flow rate range, the oil carrying capacity is bound to increase.

装载机滤芯更换时将动臂操纵杆轻推到动臂下降位置,使动臂在自重的作用下缓缓的下落,排净动臂油缸大腔中的油液,将铲斗放在地面上。将液压油箱等部件表面的污物清洗干净,以免在拆卸过程中污染液压系统。将盛油

When the loader filter replacement boom lever to nudge the boom down position, the movable arm falling under the weight of moving slowly, drain the oil arm cylinder cavity in the bucket on the ground. Clean the dirt on the surface of the hydraulic tank and other components so as not to pollute the hydraulic system during the disassembly process. Fuel oil


容器放在液压油箱的底部,拆下液压油箱底部的放油螺塞,放出液压油。拆下液压油箱加油滤芯固定螺栓,取出加油滤芯。从液压油箱上部拆开液压油回油过滤器顶盖,取出回油滤芯。拆下加油口下方的油箱清洗口法兰盖,

The container is placed in the bottom of the hydraulic oil tank, remove the hydraulic oil drain plug at the bottom of the tank, release of hydraulic oil. Remove the fixed bolt from the fuel tank and remove the filling filter. Remove the top of the hydraulic oil filter from the upper part of the hydraulic oil tank and take out the oil filter core. Remove the tank flanges at the bottom of the fuel tank.


用柴油冲洗油箱底部及四壁,最后用干净的布擦干净。使用煤油(或柴油)清洗拆下的各零部件,再用擦拭布擦拭干净并放到较密闭干净的地方(防止污染),待装。将液压油油箱的放油螺栓、回油过滤器及顶盖、加油滤芯

Flush the tank bottom and walls with diesel, finally with a clean cloth to wipe clean.  Use kerosene (or diesel) for cleaning and dismantling the parts and parts, then wipe clean and put in a more closed and clean place (prevent pollution), to be installed. The oil storage bolt, the oil back filter and the top cover, the gas filter core of the hydraulic oil tank


、油箱清洗法兰盖安装好。贵州直喷装载机销售认为从液压油加油口加入干净的液压油,油位达到液压油液位计上刻度线,拧好加油口盖。启动发动机,进行2~3次升降动臂和前倾、后倾铲斗以及左右转向到最大角度,使液

The oil tank cleaning flange cover is well installed. Guizhou Di loader sales that join the clean fluid from the hydraulic oil filling port, the oil level reaches the hydraulic oil level gauge on the line, twisting filler cap. Start the engine, carry out 2~3 lifts and forward, back and back shovel and turn to the maximum angle to make the liquid.


压油充满系统,然后铲斗在地面放平、转向对中,在怠速下运行发动机5分钟左右,发动机熄火,待液压油面平稳后,检查油位,不足时添加。贵州直喷装载机销售小编今天就分享到这里了。

The pressure oil is filled with the system, then the bucket is leveled on the ground, and the steering is on the middle. The engine runs at idle speed for about 5 minutes, and the engine stall. When the hydraulic oil level is stable, check the oil level and add it when it is insufficient. Guizhou direct injection loader sales small editor today is shared here.


本文网址:http://www.bastard-divine.com/news/358.html

关键词:贵阳直喷装载机,贵阳直喷装载机公司,贵阳直喷装载机厂家

最近浏览:

  • 在线客服
  • 联系电话
    13885175275
  • 在线留言
  • 在线咨询
    欢迎给AG8留言
    请在此输入留言内容,AG8会尽快与您联系。
    姓名
    联系人
    电话
    座机/手机号码
    邮箱
    邮箱
    地址
    地址